Repair Work Carried Out At Remote Fixer
GROHE GRONTHERM WIRELESS 45441 Repair
NO LONGER OPERATES SHOWER BUT BARELY USED FLASHES SERVICE 01 CODE WHEN BATTERIES IN IT MAY NEED TO JIG BATTERIES AROUND FOR CONNECTION
mertik maxitrol g30 g30-zrhso AND g30-zrrs Repair
tx seems ok. it lights its led on flame up (both button held) & flame down ( where only one button needs to be held). however the rx lights its led on flame down & the gas valve closes; but the led does not light on flame up & the gas valve does not open. i tested with new batteries as a matter of course.
Mertik Maxitrol G30 - ZRHDO and G30 - ZRRTT Repair
The remote and the receiver no longer seem to be in contact. Sometimes there was a slight response but not sufficient to light the fire or drive the motor. I don't know how to describe it better.
Legend fires Repair
No buttons working. Even with brand new battery. Tried taking off battery connector and going straight to battery. No joy.
Foxpro TX9 Repair
I was caught in some heavy rain and my game call remote stopped working. I dried it out at home and it seemed OK, however next time I went to use it I couldnt power it up. Tried new battery etc.
mertik maxitrol remote g30-zrhso-z26 and module g30-zrrs Repair
remote is showing red lights but does not seems to be connecting with gas fire module which is not showing any lights.
you guys have previously repaired this item, see: http://www.remotefixer.co.uk/rf1849.html
hopefully you can repair again.
thanks
cian
Marantz RC010SR Repair
volume button not working. power on/off and standby buttons not working/intermittent. Surround button intermittant
Pioneer SC-LX71 Repair
Remote powers on and looks to be working but amp does not register commands
MCHALE MK2 Auto Bale RCT2 BHC 485254 Repair
No buttons working.
Have old one as back up all working OK
MERTIK MAXITROL G30-ZRHSO Repair
Does not allow you to switch on gas fire and adjust the level of flame.The light on the control lights up when you hit the down button and the safety button with the up button, but does not start the fire. I have also supplied the receiver unit MERTIK MAXITROL G30-ZRRS.The light led does come on when you insert batteries
Mertik Maxitrol ZRHT Repair
The remote will only turn the fire down.When I press to turn fire up no signal is shown on receiver and very rarely when it does receive a signal it turns fire down instead of up.Please let me know if I should just send remote or send the remote and the receiver. Thanks
TRUMA Mover SE Repair
The unit does not switch on reliably but can usually be persuaded to work by shaking or tapping. Loose connection? There is also a rattling sound when the unit is shaken.Sooner or later it will let me down completely. The on /off switch does not move easily so needs to slid using a key but this is not in itself a problem
sun sba 2000/2080 Repair
control has been dropped a few times, and now doesn't work at all, no buttons or led
gazco mertik maxitrol G30-ZRHT Repair
The Gazco thermostatic handset/remote control: The top ("up") button no longer powers the rotary switch - to start up the fire, requiring the switch to be rotated manually.
The lower ("down") button still enables remote control of downward temperature control, and turns the fire off.
panasonic EUR7623XA0 Repair
several buttons do not work, also found poor battery connections and battery cover broken.
Metric Maxitrol G30 ZRHT Repair
The remote does not turn ON the fire but does turn it OFF (after the fire has been lit manually). The LCD display is also faulty but I'm not too fussed about that.
GETECH GE2 Repair
Battery is fully discharged after approximately a weeks use
Gazco - Mertik Maxitrol Repair
Remote buttons appear to work but signal is too weak to reach receiver from more than an inch or two PLEASE NOTE THE DISPLAY ON THE REMOTE DOES NOT WORK BUT THIS DOES NOT NEED TO BE FIXED